Standing Seam Roofing
Snap-lock and mechanical seam panels in 22 to 26 gauge steel and aluminum, Englert and Sheffield profiles, finished in 70% PVDF for high-visibility waterfront roofs.
Standing seam fabricationSERVICE AREAS / JERSEY CITY, NJ
Metal Fabricator for Jersey City, NJ
Architectural standing seam, matched siding, and edge metal cut to spec in our East Orange shop, eight miles from the Hudson waterfront. We fabricate the metal to your spec.
HUDSON COUNTY, EIGHT MILES OUT
The metal fabricator Jersey City NJ contractors order direct
U Design Fabricators is a metal fabricator Jersey City NJ roofing contractors, general contractors, and architects can order from without going through an out-of-state distributor. Our East Orange shop sits about eight miles west of the Hudson waterfront, in Essex County. We cut and form the panels to your spec, then deliver them or hand them off at the shop.
Jersey City is a dense waterfront city facing the Manhattan skyline, and the building stock shows it. High-rise and mid-rise envelopes go up where the roof, the wall, the soffit, the fascia, and the edge metal are all seen up close from the street and the river. On a job like that, appearance is the point. The metal has to read as one matched system, not a patchwork from three suppliers.
That is the work we set the shop up for. U Design has been forming panels since 2014, with more than two decades on brakes and roll formers behind the work. The envelope stays your job. The metal is ours to get right.
THE JERSEY CITY BUILDING MARKET
Waterfront envelopes where the finish is visible
The development along the Hudson runs in distinct pockets, and each one pulls metal differently. Exchange Place and the downtown waterfront carry heavy commercial and high-rise work, where the perimeter coping, fascia, and edge metal frame towers that face the river. Newport stacks mixed-use and residential mid-rise in tight blocks. Journal Square sits further inland with its own wave of mid-rise and commercial builds rising around the transit hub.
Across all three, the building envelope is high-visibility. A standing seam roof slope, the wall panels under it, and the edge metal that ties them together are read up close by anyone walking past or looking across the water. When those pieces come off different shop floors and different coils, the whites drift and the job looks pieced together. When they come off one shop in one finish family, the shell holds its color.
So the angle here is matched architectural metal for the whole shell. Standing seam plus the edge metal and siding that frame it, color-matched in the same 70% PVDF across the envelope. Premium finish work is not an upsell on a Jersey City facade. It is the spec the building was drawn to.
HOW WE FABRICATE FOR THESE JOBS
One shell, one finish family
Matched envelope
Roof panels, wall panels, soffit, fascia, and edge metal cut from the same finished stock and the same color run, so the whole shell holds one finish instead of a near-match that drifts in daylight. On a waterfront facade, that match is what people actually see.
70% PVDF, full shell
Color through our Sheffield account in 70% PVDF, the architectural finish that holds up on a high-visibility envelope facing weather off the river. The roof, the coping, the siding, and the trim carry the same finish warranty when they come from one shop.
Cut to your drawings
Send the profile, gauge, color, run lengths, and quantities, or the drawings, and we quote the panel and trim takeoff against them. Nothing is cut until the order is approved, so a mid-rise package lands at the lengths the building needs.
FROM SPEC TO THE JOBSITE
How a Jersey City order moves through the shop
- 1
Send the spec
Profile, gauge, color, run lengths, and counts, or the drawings for the envelope. We quote the panel and trim takeoff together so the whole shell is on one number.
- 2
Confirm before cutting
We confirm the spec against your drawings and the lead time against the current shop schedule. Delivery to the Jersey City jobsite is priced on the order, not added at the end.
- 3
Fabricate to match
Panels and trim are cut and formed from one finish family in the East Orange shop, so the roof, wall, and edge metal carry one color across the building.
- 4
Deliver or pick up
We deliver to the jobsite or you load at the shop, eight miles back. For long runs that are hard to ship intact, panels can be roll-formed on site to field lengths.
WHAT WE FABRICATE FOR JERSEY CITY
Five panel lines for the full envelope
Each line is cut to spec in East Orange and delivered to the Jersey City jobsite or picked up at the shop. Order them together and the whole shell arrives color-matched.
Edge Metal and Flashing
Coping, fascia, gravel stop, and perimeter edge metal, color-matched to the panels so a high-rise perimeter reads as one continuous line from the street and the river.
Edge metal fabricationMetal Siding Panels
Concealed and exposed-fastener wall panels in the same steel and aluminum as the roof line, color-matched across the mid-rise and mixed-use envelope, architectural to industrial.
Metal siding fabricationCustom Fabrication
Counter flashing, scuppers, leader heads, and one-off brake-formed trim cut to your sketch, CAD file, or sample, formed from the same finished stock as the rest of the order.
Custom sheet metalSoffit and Fascia
Soffit and fascia formed to match the roof and wall finish, so the underside and edge of a Jersey City envelope carry the same color as the metal above them.
Soffit and fascia fabricationJERSEY CITY QUESTIONS
Common questions from Jersey City contractors
Are you a metal fabricator Jersey City NJ contractors can order from directly?
Yes. Roofers, GCs, and architects order from the shop direct, no distributor in the middle. Send the spec or drawings, and we quote the panel and trim takeoff for the Jersey City job and confirm delivery on the order.
Do you install on Jersey City jobsites?
Fabrication is the focus. We cut and form the panels and trim to your spec and deliver them or hand them off at the shop, ready to set.
How far is the shop from Jersey City?
About eight miles. The East Orange shop sits in Essex County, a short run west of the Hudson waterfront. That keeps delivery to a downtown, Newport, or Journal Square jobsite practical, and pickup at the shop is an easy round trip for a local crew.
Can you match the roof, siding, and edge metal on one envelope?
Yes, and on a high-visibility Jersey City building that is the point. We cut the roof panels, wall panels, soffit, fascia, and edge metal from one finish family and one color run, so the whole shell holds the same color instead of a near-match that drifts.
What finish do you fabricate for waterfront buildings?
70% PVDF, sourced through our Sheffield account. It is the architectural finish that holds color and stands up on a high-visibility envelope facing weather off the river. Aluminum is on hand for the jobs closest to the water that want the corrosion resistance.
Do you deliver to high-rise jobs with tight street access?
We deliver to Jersey City jobsites and price the delivery on the order once we have the address. For long runs that are hard to ship intact, panels can be roll-formed on site so full-length panels come off the machine at the building.
Can you fabricate from architect drawings?
Yes. Send the drawings and we quote the panel and trim takeoff against them, flagging anything that should be a special color or substrate. Nothing is cut until the spec is confirmed and the order is approved.
Do you work in Portuguese?
Yes. The shop runs in English and Portuguese, so you can send a spec, talk through a profile, or sort out a takeoff in either one. You reach the shop floor directly, not an out-of-state account desk.
Have a Jersey City envelope to fabricate?
Send the profile, gauge, color, and quantities, or the drawings, and we quote the panel and trim takeoff together with delivery to the jobsite. Pickup in East Orange is always open.